Electric Motors

61 - 80 of 149

Key Features


  • Epoxy Painted
  • Standard NEMA Shaft extension
  • Class F insulation
  • Epoxy paint

Check Inventory


Key Features


  • DPA0 - Drip Proof Air Over IP22,Motor venting protected against insects and rodents, Rolled steel construction
  • Two Nameplates, 1 stamped with MIN AIRFLOW REQUIRED OVER MOTOR IS 600FPM
  • Capacitors shipped loose on 1-phase designs, Gasketed capacitor cases and conduit box covers
  • Meets or exceeds NEMA® service factors
  • 34” long leads
  • Double shielded ball bearings, Keyed shaft with 1/4-20 UNC tapped hole on end
  • Class F Insulation with Class F T-Stats
  • UL recognized component listing and CSA certified

Check Inventory


Key Features


  • 213/215TZ models have 1-1/8” shaft, 182TZ model has 7/8” shaft
  • Manual reset thermal protector
  • Condensate drains
  • Capacitor start induction run design
  • F1 mounting only, cannot reassemble to F2

Check Inventory


Key Features


  • 213/215TZ models have 1-1/8” shaft, 182TZ model has 7/8” shaft
  • Manual reset thermal protector
  • Condensate drains
  • Capacitor start/capacitor run design for reduced amperage

Check Inventory


Key Features


  • IP-22 rolled steel, Meets or exceeds NEMA Premium®* efficiencies, NEMA Premium models are in compliance with EISA2007
  • Class F Insulation System, Inverter duty 10:1 variable torque and 2:1 constant torque & 1.15 service factor on Sine Wave Power 1.0 SF on Inverter Power
  • F1/F2 capable, Dynamically balanced rotors, Steel conduit box
  • Dual Frame Mounting, 1.625" x 5.00" Shaft Extension, Bearing Caps both ends, Grease Fitting With Pipe Plugs
  • Modifications and Kits are available, Drip Cover Provisions
  • 40°C Ambient 1.15SF Sine Wave Power and 1.0SF inverter power
  • UL®* listed, UL certified for Canada and CE®* mark

Check Inventory


Key Features


  • High starting torque
  • Removable condensate drain plugs
  • Manual reset thermal protector
  • All parts are corrosion resistant

Check Inventory


Key Features


  • Double sealed ball bearings
  • Thermostats for thermal overload protection (auto reset protector on Z304)
  • 34” long leads for ease of installation
  • Keyed shafts with 1/4”-20 UNC tapped hole in end
  • Extra nameplate included, loose, for remote mounting

Check Inventory


Key Features


  • High starting torque
  • Removable condensate drain plugs
  • Manual reset thermal protector
  • All parts are corrosion resistant

Check Inventory


Key Features


  • Shaft end mechanically locked on C-face models
  • Shaft slinger
  • Low temperature manual reset thermal protector
  • Condensate drains

Check Inventory


Key Features


  • Premium efficient designs
  • Double sealed ball bearings
  • Shaft flinger - output shaft
  • Normally closed thermostat protected
  • Weep holes provide condensation drains

Check Inventory


Key Features


  • High starting torque
  • Removable condensate drain plugs
  • Manual reset thermal protector
  • All parts are corrosion resistant

Key Features


  • Double sealed ball bearings
  • Thermostats for thermal overload protection (auto reset protector on Z304)
  • 34” long leads for ease of installation
  • Keyed shafts with 1/4”-20 UNC tapped hole in end
  • Extra nameplate included, loose, for remote mounting

Key Features


  • Double sealed ball bearings
  • Thermostats for thermal overload protection (auto reset protector on Z304)
  • 34” long leads for ease of installation
  • Keyed shafts with 1/4”-20 UNC tapped hole in end
  • Extra nameplate included, loose, for remote mounting

Key Features


  • High starting torque
  • Removable condensate drain plugs
  • Manual reset thermal protector
  • All parts are corrosion resistant

Key Features


  • Shaft end mechanically locked on C-face models
  • Shaft slinger
  • Low temperature manual reset thermal protector
  • Condensate drains

Key Features


  • Cast aluminium construction
  • Energy efficient

Key Features


  • Double sealed ball bearings
  • Thermostats for thermal overload protection (auto reset protector on Z304)
  • 34” long leads for ease of installation
  • Keyed shafts with 1/4”-20 UNC tapped hole in end
  • Extra nameplate included, loose, for remote mounting

Key Features


  • Class “F” insulation system
  • Overload protected
  • Keyed shaft with 1/4-20 UNC tapped hole on end
  • 34” long leads
  • Motor venting protected against insects and rodents
  • Double sealed ball bearings

Key Features


  • Premium efficient designs
  • Double sealed ball bearings
  • Shaft flinger - output shaft
  • Normally closed thermostat protected
  • Weep holes provide condensation drains

Key Features


  • Thermostats for thermal overload protection
  • 34” long leads exit elbow connector in bracket
  • Keyed shafts with 1/4”-20 UNC tapped hole in end